Gold metal loss calculator for jewelry manufacturing

Weigh what you issued to the bench, what came back as finished work and what you saved as scrap. The calculator shows the metal you lost in grams, as a percent, as fine gold and in dollars at the gold price you type.

The calculator needs JavaScript. The worked example below shows the same math by hand.

How the math works

Metal lost is the metal issued, less the finished weight, less the scrap you weighed back. The loss percent is that loss divided by the metal issued.

Only part of karat gold is gold. 14K is stamped 585, so it is 58.5% gold. Fine gold lost is the metal lost times that share. The calculator uses the stamped share for each karat: 10K is 41.7%, 14K is 58.5%, 18K is 75%, 22K is 91.6% and 24K is 99.9%.

Gold is priced by the troy ounce, and a troy ounce is 31.1034768 grams. So the dollars lost are the grams of fine gold, times the price, divided by 31.1034768.

A worked example

You issue 120.00 g of 14K to the bench for 20 rings. The finished rings weigh 108.60 g. You weigh back 9.90 g of sprues, buttons and filings. Say gold is $4,000 a troy ounce.

  • Metal lost: 120.00 - 108.60 - 9.90 = 1.50 g.
  • Loss: 1.50 ÷ 120.00 = 1.25% of the metal issued.
  • Fine gold lost: 1.50 × 0.585 = 0.8775 g.
  • Dollars lost: 0.8775 × $4,000 ÷ 31.1034768 = $112.85.
  • Per ring: 0.075 g of metal, or $5.64 of gold.

The 9.90 g of scrap holds 5.79 g of fine gold. At the same price that is $744.80 of gold. That is why it gets weighed and saved.

Where the metal goes

Casting. The sprue and the button come back as scrap. Some metal still goes. It burns off in the melt, sticks in the crucible or spills.

Filing. Filings fall to the bench pin and the skin under it. What you catch is scrap. What lands on the floor or your apron is loss until the sweeps go out.

Polishing. The wheel takes metal off as dust. Most of it ends up in the polishing machine's filter, the rags and the sweeps.

Setting. Cutting seats and raising beads takes small chips of metal. They are easy to lose.

Why recovered scrap matters

Scrap is still gold. Sprues, buttons, filings, polishing dust and floor sweeps go back to the refiner. The refiner pays you for the gold in them, less its own charges. Weigh scrap back every time. If you don't, it reads as loss, and your loss looks worse than it is.

Questions

Questions

How do I work out metal loss in jewelry manufacturing?

Take the metal you issued to the bench. Subtract the finished weight and the scrap you weighed back. What is left is your loss. Divide it by the metal issued for the loss percent.

Why does 14K count as 58.5% gold here?

14K is stamped 585, which means 585 parts gold in 1,000. The calculator uses the stamped share for every karat, so 18K is 75% and 22K is 91.6%.

What if the finished weight plus scrap comes to more than I issued?

That can't happen at the bench, so a number is wrong. A weight was entered wrong or a scale is off. Check the entries, then weigh again on the same scale.

Should I count scrap as loss?

No. Scrap you weigh back goes to the refiner, and you get paid for the gold in it. Only metal you can't weigh back is loss.

Is the dollar figure what my refiner will pay?

No. It is the gold at the price you typed. A refiner settles on its own terms and takes its own charges. Use the figure to see what the loss costs you in gold.

Work orders carry a piece from wax to QC, one stage at a time. Metal is weighed out to the job and back as metal and scrap. Karatry shows the loss on every job, by the gram.